Replacment - Repair PEM for Parker / Bolston, Packard and Scott Hydrogen Generators - a possibly some others.  115 Nafion coated Platinum black on one soide and  Iridium Ruthenium Oxide on the other.  If your generator does not develop pressure and / or has water on the Hydrogen side - then the membrane is likely got a hole in it and THEY CANNOT BE REPAIRED - but only replaced.  This membrane is higher performance than what was in there.  Custom made

This KIT is cut electrode plates,electrode separators, stainless wire to connect the electrodes, and  gasket structure items ONLY and of course the instructions / plans a list of materials needed to do so.  A full kit with control items is here.

This can be used to store hydrogen for a dedicated on the fly system for quick start so as to not wait for pressure to build for our separated gas Hydrogen systems.

Actual item NOT pictured.

This is a custom part upon ordering is not refundable nor will be returnable.

Will partly recharge with a lengthy drive depending on pressure

The Gas Generator is not included in this price.  You will need a separated gas generator or source that can maintain approximately 30 to 45 psi

The BASIC KIT is cut electrode plates, two end plates, electrode separators, and  gasket structure items along with electronic controls for the unit when built - and of course the instructions / plans to do so.  Requires assembly similar as shown in the Gashole Plugged video.  No wiring or pumps or other plans; however it is a wet cell design which will not clog and is a low (under 30 psi) pressure type wet cell design.  Easy to assemble.  Wiring and plumbing is a bit more tricky.  Custom Made Item Not Refunable or Returnable

Onboard Hoffman design type Generator hydrogen gas-from-water generator by miniaturizing our electrolyzer technology to fit onboard a vehicle so you can add hydrogen gas into your engine without hydrogen gas storage tanks via a real SPE/PEM electrolyzer: Solid Polymer Electrolyte SPE / Proton Exchange Membrane PEM hydrogen-gas-from-water electrolyzer.  It can be adapted to be used in moderate freezing climates by using anti-freezing fuel stock.

This will reduce your emissions and fuel costs plus extend your mileage with more onboard autonomy.

These are the two things you need but might not find locally to build a pressurizing gas system.

The regulator can be adjusted to control the pressure of the gas generator.and the switch is phenolic - not actual pictures

This is a custom part upon ordering is not refundable nor will be returnable.

Fuel injection systems operate between 30 and 60 PSI depending on the size of the injectors and amount gas needed.

Hard to find materials ONLY to make a high pressure gas generator round enclosure like our separated gas unit.

This will make a 6 inch round by 1 foot tall enclosure Rated with a maximum burst pressure of 560 PSI and an operating pressure of 120 psi. 

You will need to drill and cut as required for your design or tap and/or glue fittings in for your lines as you desire.

This is a custom part upon ordering is not refundable nor will be returnable.

Horizontal float switch.  Use in filling circuit with a Relay.  100 PSI max.  Polypropylene.  White. 

Contact Rating   70VA/ 50W 

Type    SPST 

Max Switching Voltage  150VAC /200VDC  

Max Switching Current  0.7A AC /1.0A DC

Wires     22 awg PVC 2

Operating temperature   -15 TO 221'F
        

Ideal for high temperature and pressure applications. Rugged construction allows these units to be used for reliable switching in a wide variety of chemicals, oils and water in harsh environments.

This is a custom part upon ordering is not refundable nor will be returnable.

Horizontal float switch.  Use in filling circuit with a Relay. 

500 PSI max.  Stainless Steel. 

Contact Rating   70VA/ 50W 

Type    SPST 

Max Switching Voltage  150VAC / 200VDC  

Max Switching Current  0.7A AC /1.0A DC