PEM Full FreeFuelSystem
Custom made electrical item NOT Returnable or Refundable
[ You can opt out of Google Ads if you are a registered user at /ad-options ]
Custom made electrical item NOT Returnable or Refundable
Mis-packaged 1187k6. New. Immediate shipping
Hard to find materials ONLY to make a high pressure gas generator round enclosure like our separated gas unit.
This will make a 6 inch round by 1 foot tall enclosure Rated with a maximum burst pressure of 560 PSI and an operating pressure of 200 psi and 200 degrees Fahrenheit
This is a custom part upon ordering is not refundable nor will be returnable.
This will reduce your emissions and fuel costs plus extend your mileage with more onboard autonomy.
Custom made electrical item NOT Returnable or Refundable
Available in four versions
1. Home / Business stationary version - 110 or 220 volt
2. Small engine genset air cooled engine generator version 12 volt kit
3. 12 volt version
4. 24 volt version
Custom made electrical item NOT Returnable or Refundable
This item makes 99.99 percent PURE Hydrogen.
To run an engine the amount of hydrogen required is determined by the size of the engine. 0.15 Litres/minute per 1L of engine size is ideal. For example, a 3L engine will achieve best results with a generator producing hydrogen at a rate of 0.5 L/minute. Hydrogen supplementation is subject to the law of diminishing returns.
For bifueling less can be used so select the size you want in the add to cart
This is a custom item upon ordering is not refundable nor will be returnable.
The franchise documents are sent to you be whatever selected method. It is an annual license fee.
You should have started at https://hydrogenfuelingplace.com/great_investment_opportunity or
https://hydrogenpowercentral.com/great_investment_opportunity or
Ideal for high temperature and pressure applications. Rugged construction allows these units to be used for reliable switching in a wide variety of chemicals, oils and water in harsh environments.
This is a custom part upon ordering is not refundable nor will be returnable.
Vertical float switch. Use in filling circuit with a Relay.
300 PSI max. Stainless Steel.
Contact Rating 70VA/ 50W
Type SPST
Max Switching Voltage 150VAC / 200VDC
Max Switching Current 0.7A AC /1.0A DC
Pure Hydrogen can be made from Aluminum and Lye by the following equation
Sodium aluminate is produced and pure Hydrogen Gas
2 Al + 2 NaOH + 2 H2O → 2 NaAlO2 + 3 H2
See https://en.wikipedia.org/wiki/Sodium_aluminate
What is the story of the GM 6.5 - why is it blowing PMD's ??. Short answer is the Lift Pump
0-5v - 0-300 psi for our digital pressure gauge => https://bigbay4bestbuys.com/content/hydrogen-purity-gauge-and-controller
ACDELCO 17113573 fuel Injector - used condition unknown |
UPC 036666963410
DR151B Voltage Regulator for 12 SI
UPC 707390533056
Put any special requests in the notes section at checkout - if it cannot be done your money will be refunded immediately
MS 1454P-30 Bearings (.030 oversize)
Fits also SBC V-8 by buying an extra main set
UPC 027067552969
Put any special requests in the notes section at checkout - if it cannot be done your money will be refunded immediately
CB 1358P_020-6 Clemex Rod Bearings (.020 oversize)
Interchanges with 1020 CP Rod Bearings
UPC 645181014943
Put any special requests in the notes section at checkout - if it cannot be done your money will be refunded immediately
CB 1358P STD Clemex Rod Bearings
Interchanges with 1020 CP Rod Bearings
UPC 645181014950
Put any special requests in the notes section at checkout - if it cannot be done your money will be refunded immediately
1020 CP Rod Bearings
UPC 724856232130
Put any special requests in the notes section at checkout - if it cannot be done your money will be refunded immediately
For Lift Pump Pressure . You can leave this gauge permanently in place so you can check your pressure anytime to get on top of diagnosis of problems.
Includes a 1.5" Liquid Filled stainless case gauge and with brass internals. Also includes a solid brass in-line fuel gauge adapter to mount on TOP of the Schrader valve - after you remove the core to mount it right on your fuel line on most 6.5's just before the IP inlet.
Replacment - Repair PEM for Parker / Bolston, Packard and Scott Hydrogen Generators - a possibly some others. 115 Nafion coated Platinum black on one soide and Iridium Ruthenium Oxide on the other. If your generator does not develop pressure and / or has water on the Hydrogen side - then the membrane is likely got a hole in it and THEY CANNOT BE REPAIRED - but only replaced. This membrane is higher performance than what was in there. Custom made
This KIT is cut electrode plates,electrode separators, stainless wire to connect the electrodes, and gasket structure items ONLY and of course the instructions / plans a list of materials needed to do so. A full kit with control items is here.
It ain't rocket science but there is more to it than you think
Copyright © 2024,