Cetane, BTU and Lubricity Enhancer for poor Diesel Fuel

[ You can opt out of Google Ads if you are a registered user at /ad-options ]
$9.99
型号: cetane_booster

Make your diesel run at its best.   Cetane is an index or number that is the measure of how easily a diesel fuel spontaneously lights when injected.  It is the flash point at a certain temperature.  It is NOT a measure of BTU per gallon or Lubricity. Poor diesel fuel also contributes to clogging the injectors because it burns cooler and in a more sooty incomplete fashion and especially in pre-chamber diesels like the GM 6.5 part of that unburnt fuel is actually pushed back into the injector when it explodes as the injector is injecting fuel and some of it is often just a little bit forced back into the injector. 

"A little bit" of a clog is all it takes to make an injector perform poorly and imbalance the diesel  injection process and if you do not have slippery fuel that helps wash it through and back out - the result is a sticking injector which on at least the GM 6.5 sounds a connecting rod knocking especially at low rpm  Another thing that contributes to this is poor fuel pressure to the injection pump itself at least on the GM 6.5 resulting in poor and non-uniform "pop" injection pressures which causes the same thing.  It happens on direct injection diesels also and in Ford Powerstrokes and other International Harvester commonly known as  HEUI design engines the injectors suffer from what is called a "stiction" problem and in the end it causes the same result and those injectors are really expensive.  A good injector cleaner may dissolve the carbon over time and push it out and through, but why cause the problem in the first place??

Fuel additives for diesel fuel is expensive and ALL of them on the market add OVER 13 cents per gallon - and the highest adds 60 cents per gallon - to the cost of each gallon of fuel.  Additionally you do not know what you are really getting.  You are paying for a brand name and costs of distribution.  This item is not refundable or returnable

[ You can opt out of Google Ads if you are a registered user at /ad-options ]

The data sheets are available for most all additives out there - but ours only adds about 3 cents to a gallon of fuel.  Our product is the one single thing you cannot buy, and a recipe of the others to make enough fuel to treat up to 1,000 gallons of fuel.

When you hear noise and rattling - most people say "oh that is just how a diesel runs"; but actually no - that is ignition delay caused by poor fuel - low cetane fuel.

The US government only requires 40 cetane of diesel at the pump, and worse - NO ONE checks this, and unless you are diligent and have a fuel hydrometer - you cannot either.

Worse yet - diesel fuel today is being blended and encouraged to be made from animal fat and plant-stock called collectively "bio-diesel"; burns at lower temperatures to encourage lower NOx formation.  It will not burn CNG or LPG well bi-fueled (fumigated) and usually burns pure Hydrogen well - but not always "HHO" well, so you want to "warm" its burning temperature back up higher, or it is just plain sluggish fuel. See https://bigbay4bestbuys.com/NOx_and_the_Diesel

Many traditional diesel Injection Pumps today are sensitive to the ULSD fuel sold at the pump which has lower lubricity than it once did - and the truth is to get to the 15 ppm level of Sulfur allowed, actually MORE lubricity comes out than is safe for many engines and their injection systems - so the refineries are SUPPOSED to add lubricity enhancer, and at the same time stripping the sulfur also strips some BTU per gallon and effectively lowers the Cetane NUMBER - so to improve that they put in an additive to increase the Cetane INDEX.  But do they ???

Here is what ULSD is in loss of BTU per gallon compared to straight Diesel - named only home heating oil - they are the same product you know

  • 1 gallon of gasoline = 120,405 Btu   (according to eia.gov)
  • 1 gallon of diesel fuel = 137,381 Btu (distillate fuel with less than 15 parts per million sulfur content)    (according to eia.gov)
  • 1 gallon of heating oil = 138,500 Btu (distillate fuel with 15 to 500 parts per million sulfur content)   (according to eia.gov); HOWEVER,
  • The BTU value of 2 cycle oil is 138,000 BTU/gallon and diesel fuel can actually vary from 126,000 to 133,000 BTU/gallon in most places - lower BTU than the "published government standard" one would expect

In the refining / oil business things that are largely equivalent products are simply "named" differently and most consumers buy the name and do not know what they are really buying,  You see no one measures the Cetane or BTU content of most common diesel fuel - and only the "big refineries" that charge a premium cost for Diesel actually make sure their product rolls out the door at a standard Cetane - which is usually higher so there customers can feel the difference.  This is a well known Internet list 

Propel HPR, 75  (Techically a type of BioDiesel - though Propel says it is not BioDiesel BUT it is LOW in BTU per gallon and you will feel the lack of power with a real quiet, easy starting engine though)
Syndiesel, 60
BP (Amoco branded), 51
Countrymark fuels Diesel-R, 50
Chevron, 49; or 51 with Techron D labels in select markets
ConocoPhillips through the 76 stations (California) 47-53
PetroCanada, 47-51
BP (Powerblend 47, otherwise 40-42)  (Includes ARCO brand as "OTHERWISE")
Shell, 46; 
Sinclair, 46; 
Sunoco Gold, 45 (often +1-5) Sunoco regular is usually 40.
Exxon/Mobile, 43-46
Holiday Stations, 40-43
HESS, 40-42, can be up to 45.
Husky, 40 + diesel Max additives raise another 1-3 from there (41-45 max)
Pilot/Love's/Flying J/Valero/Sheetz/Walmart/Wawa: 40

The difference in price between ARCO and Chevron in most places visited and viewed as to pricing is 60 to 70 cents per gallon - SERIOUSLY - there is a better way and it is this Cetane booster additive.

It should be noted that allegedly in California all Diesel is "supposed" to by law be 53 Cetane.  See https://www.arb.ca.gov/enf/fuels/dieselspecs.pdf - but that is not believable in practice as real world use of the fuel finds it to be unremarkable low in "power'.

Below is a chart of many of the Diesel additives available today from a lubricity study done with various additives by Southwest Research after the change over to ULSD in 2007. The maximum score allowed by the government on the HFRR wear scare measurement test is 520 microns for diesel fuel. The engine manufacturers association would like that number to be lower and set at 460 microns, thus the lower the HFRR score the better. 2 cycle oil is #7 in this test at what is about .65 ox per gallon -or a little more than half an ounce per gallon.  Remember this ALSO lowers the cetane of the fulel but increases the lubricity.  Thus in this case you trade performance and easy starting for lubricity.  it is also like to smoke more and you will get slightly poorer mileage.  Be SURE and look at the cost per tank it adds - in 2007 dollars - per 26 gallons.  in almost EVERY case again - our additive adds between 75 cents to less than 1 dollar USD - per 26 gallons of fuel.

This test took untreaded diesel fuel (since the lubricity additives are not added at the refinery but at the terminal) and tested it with each additive to show which additive will bring untreated diesel fuel within the specification.  (you can right click on the chart study image and "open in new tab" or "view image"  for a larger view of the study chart in another browser window)

DIESEL FUEL LUBRICITY ADDITIVES STUDY RESULTS

Products 1 through 4 were able to improve the non-additized fuel to an HFRR score of 460 or better. This meets the strictest requirements requested by the Engine Manufacturers Association.

Products 1 through 9 were able to improve the non-additized fuel to an HFRR score of 520 or better, meeting the U.S. diesel fuel requirements for maximum wear scar in a commercially available diesel fuel.

Products 16 through 19 were found to cause the fuel/additive blend to perform worse than the baseline fuel. The cause for this is speculative. This is not unprecedented in HFRR testing and can be caused by low lubricity solvents like  alcohol or other components in the additives. 

Since 2007 some companies have adjusted their formula in order to be more effective with ULSD.

In all cases, one must analyze how much you initially save or it costs you to by low quality fuel in the first place

Now, this study strictly looks at lubricity. But you also want other qualities in a diesel fuel additive. 

1. a detergent that for instance passes the Cummins L-10 Injector Depositing Test and Cummins N-14 Injector Corrosion Test Performance.

2. A cetane improver - and trhat is what this additive is about both lubricity and cetane improvement

3. a non-alcohol based deicer/water dispersant for climates that need anti-gelling.

One cannot go wrong with the top 9 in this survey as far as lubricity is concerned. But you need to keep in mind the other qualities listed above and the overall cost involved as well as BTU per gallon effects.

For instance you get 40 MPG from Flying J at $4.25/gallon, and 45 MPG from Chevron/BP at $4.49/gallon, you are paying $.10625/mile with the J, and $.09978/mile with the higher quality fuel. (And if you find a quality station next to a truck stop often the difference in price is less than $.05/gallon!) You actually save $64 just in fuel over the course of 10,000 miles by buying the more expensive fuel. This says nothing for what you might save in maintenance (injection pump and the rest of the fuel system) over the course of time. Just because it's expensive doesn't mean it's good, but why buy more expensive fuel when you can make it yourself for about three cents more per gallon ??  Remember high Cetane does noean high BTU per gallon and that is what translates into higher mpg along with higher Cetane.  Higher BTU is more powerful bang - and high Cetane is better, faster more immediate access to the bang.  In proper terms high Cetane is shorter ignition delay (why a diesel rattles) and higher BTU per gallon is more power on that stroke of the bang.  BTU takes you farther - and higher Cetane makes it happen faster and a more complete burn - which is also less black smoke.  Note that two known low BTU per gallon high Cetane fuels are Propel's HPR (as it is a Biodiesel) and Biodiesel in general.  See http://www.afdc.energy.gov/fuels/fuel_comparison_chart.pdf and https://en.wikipedia.org/wiki/Energy_content_of_biofuel - and compoare the biofuels to fossil (petrroleum based) fuels.

Keep in mind that the current minimum from refiners in North America is 40 by law. Depending on the quality of the oil used as well as refining processes you'll find 40-42 from refiners in the US and Canada. Anything above that has to do with specific companies additives put in at the refinery. When companies give a minimum value then it will be listed as a single number. When a company gives a range of numbers bear in mind that more often than not you'll probably find the lower number rather than the higher number. If 40 is listed then it generally means that fuel is bought as is from the refiner; but if someone screws up and doesn't put in enough additive at the refinery then that can cause major problems for your fuel system and it could be more like 36 to 38 Cetane instead. If you get the inexpensive fuel with low cetane you use a cetane booster (PowerService, Lubromoly Cetane booster or Stanadyne are all great and EXPENSIVE choices), or run a little biodiesel in the tank whicvh will boost Cetane but LOWER BTU per gallon. If something higher than 42 is listed then the retailer adds their own additive package in addition to the standard refinery additive package. Generally speaking as long as 49 or higher is listed you do not need to worry about adding any additives yourself.

Cetane number ( https://en.wikipedia.org/wiki/Cetane_number ) is NOT the same as Cetane Index  ( https://en.wikipedia.org/wiki/Cetane_index ) but the use of the Index is a way to make low BTU fuel meet a higher Cetane for marketing - as one needs both high BTU per gallon and high Cetane - to make a superior Diesel fuel - and with this additive you are in charge of inexpensively bringing UP that number when you get a poor load of diesel.  What is left out is the lubricity issue all together.

The two Cetane measurements are conceptually the same but in reality they are not.  The Ford Powerstroke diesel and many other International Harvester (IH) DT type engines (the Powerstoke is an International Harvester engine) suffer from "stiction" in part due to ULSD and the lack of lubricity.  Mechanical injector engines like the GM 6.5 can experience sticking injectors that sound like rod knock.  The GM 6.5 also has an immersion lubrication injection pump which greatly benefits from the added lubricity such to the point you will likely hear rubbing and metal on metal grinding noises subside.  Lots of people have replaced injectors and Injection Pumps and never knew it was the fuel over time tearing up their investment

This additive solves both issues and you will hear a quieter engine and experience more power, because in its use you raise the BTU per gallon, raise the lubricity AND raise the cetane INDEX.  Raising BTU per gallon has little value if you do not also raise the cetane INDEX

This is a concentrate and you mix up to 3 gallons with it that you use at the rate of 1 half to 1 oz per gallon - depending on where you buy diesel it quality - and boy you will glad you did

4 oz bottle makes up to 384 ozs - 3 gallons which you use at the rate above so that 1000 gallons of fuel can be treated.  this is the same additive the refineries and other additive manufacturers  use in a consumer size

 

UC_Image: 
English(英语)
价格: $9.99
权重: 0.75 lb
尺寸: 10 in × 8 in × 0.5 in
[ You can opt out of Google Ads if you are a registered user at /ad-options ]